ÃÀ¼§¸ó

To inform you of the different types of gas turbine engines; their applications, on-design, off-design and transient performance.

To provide you with the ability to undertake gas turbine component performance calculations, diagnostics and to perform evaluations of gas turbine performance, and deterioration.

Gas Turbine Types and Applications

Effect of design parameters such as pressure ratio and turbine temperature on the basic gas turbine cycle. Modifications of the basic Brayton cycle, compounding, intercooling, reheating, heat exchange, bypass, and fan cycles. Simulation of the above.

Performance and Simulation

Design point performance of turbojet, turbofan and turboshaft cycles, effect of bypass ratio. Off design performance, effect of ambient temperature, altitude, throttle setting and flight speed. Non-dimensional representation. Gas turbine simulation. Effects of bleeds and power offtakes. Compressor turbine matching. Gas turbine degradation. Simulation and diagnostics of the above. Component maps. Surge alleviation, performance improvements, steady-state, and transient performance. Off-design performance calculations and iteration techniques Accelerations, decelerations, effects on surge margin. Transients of single shaft and multi-shaft engines. Transient performance simulation. Effects of heat transfer on transient performance.

Software used for gas turbine performance simulation: TURBOMATCH

Diagnostics and Monitoring.

Description of gas turbine performance degradation and faults.

Description of most used gas turbine condition monitoring techniques.

Software used for diagnostics: PYTHIA

On successful completion of this module you should be able to:

1. 1. Examine the gas turbine components and evaluate the performance in terms of power, thrust and specific fuel consumption of various types of gas turbine engines.
2. 2. Assess the results from quantitative evaluations of gas turbine designs to determine appropriate power or propulsion systems for different applications.
3. 3. Set up numerical iterative methods for the matching of engine components to generate the engine running line.
4. 4. Assess the impact of different degradation and faults on gas turbine performance.
5. 5. Assemble computer based simulation and diagnostic analysis tools to simulate engine performance and detect its faults.

To familiarise you with compressor and turbine aerodynamic design and performance by instruction, investigation and example.

To introduce you to the technology of gas turbine blade cooling through analytical and practical approaches of heat transfer principles, convection cooling, impingement film transpiration cooling and liquid cooling.

Thermofluids: Introduction to aerodynamics, thermofluids, and compressible flows.

Compressor Design and Performance

Overall performance:  Fundamentals of axial flow compressors.  Overall performance, achievable pressure ratio and efficiency. The effect of Reynolds number, Mach number, and incidence. Definition of isentropic and polytropic efficiency, effect of pressure ratio, performance at constant speed, surge and surge margin definitions, running line, choking effects.

The axial compressor stage: Stage loading and flow parameters, limitation in design on pitch line basis. Definition and choice of reaction at design, effect on stage efficiency. Loss sources in turbomachines and loss estimation methods. The ideal and real stage characteristic, stall and choke. The free vortex solution, limitations due to hub/tip ratio. Off-design performance Choice of overall annulus geometry, axial spacing, aspect ratio, limitations of rear hub/tip ratio. Compressor blading: selection of blade numbers, aspect ratio and basic blade profiling.

Compressor design example: Multi-stage compressor design example carried out for a HPC.

Turbine Design and Performance

Overall performance: the expansion process and characteristics, annulus layout and design choices, choice of stage loading and flow coefficient, engine overall performance requirements, overall annulus geometry and layout; rising line, constant mean diameter and falling line.

The axial turbine stage: Aerodynamic concepts and parameters, velocity triangles, reaction, stage loading, flow coefficients. The ideal and real characteristic. Design  for maximum power: effect of choking and change of inlet temperature and pressure.  Stage efficiency, overtip leakage, profile losses, correlations. Three-dimensional design aspects. Radial equilibrium and secondary flows.

Turbine blading: choice of base profile, blade numbers and aspect ratio. Zweiffel's and alternative lift coefficients.

Turbine Design Example: An aerodynamic design example is carried out for a HPT Heat Transfer Principles: Brief review of heat transfer principles and physical significance of non-dimensional groupings. Conditions around blades, boundary layers, external heat transfer coefficient distribution, effect of turbulence. Root cooled blades and NGVs, analytical and numerical methods of determining spanwise temperature distribution. Fibre strengthened and nickel base alloys.

Need for high turbine entry temperature: effect on engine performance.

Development of materials, manufacturing processes and cooling systems.

Convection Cooling: Convectively cooled aerofoils: analytical approach for metal and cooling air spanwise temperature distribution. Cooling passage geometry and heat transfer characteristics. Cooling efficiency, cooling effectiveness and mass flow function: application at project design stage for determining metal and cooling air temperatures. Methods for optimising cooling system design: secondary surfaces and multipass. Internal temperature distribution of cooled aerofoils: calculations, comparisons with experimental results.

Impingement, Film and Transpiration Cooling: Principles steady state and transient performance, characteristics, advantages, limitations, comparison with convection cooling. Cooling air feed and discharge systems. Integration of cooled turbine with aerodynamic performance and main engine design. Co-ordination of design responsibilities. Example of cooled turbine stage design.

Liquid Cooling: Liquid cooling: principles, advantages and limitations, practical examples.

On successful completion of this module you should be able to:

1. 1. Identify and analyse the design and performance characteristics of turbomachinery components.
2. 2. For given inlet conditions and requirements, determine the aerodynamic performance characteristics of a turbomachine and comment on the feasibility of the design.
3. 3. Differentiate the key design choices for axial compressors and turbines, Construct an assessment of the aspects which affect the design and performance of axial turbomachines an apply formulations and critical evaluations of underpinning turbo-machinery theories.
4. 4. Explain the requirement for ethical and professional conduct in the use of data and in the presentation of results and calculations.
5. 5. Explain the major differences between the various heat transfer and cooling architectures and apply the concepts and theories of heat transfer and different cooling technologies to the cooling of turbine blades to produce a realistic assessment of their cooling requirements.

To make you familiar with design, operation, computation and performance criteria of gas turbine (GT) combustion and reheat systems and to explore issues related to gas turbine pollutant emissions.

Introduction to GT combustor design considerations and sizing methodologies:

Diffusion and pre-mixed flame characteristics; GT combustor design features and performance requirements; Design considerations and main functions of the primary, intermediate and dilution zones; Fundamental aspects of the ignition process; Sources of pressure loss; Performance criteria and requirements for pre-combustor diffusers; Faired and dump diffusers; Combustor sizing methodologies based on the pressure loss approach, combustor efficiency requirements and altitude relight requirements.

Combustion efficiency:

Definition of combustion efficiency and combustion efficiency requirements; Evaporation rate controlled systems – influence of fuel type, turbulence and pressure, drop size and residence time; Mixing rate controlled systems; Reaction rate controlled systems – derivation and significance of the “q” parameter.

Overview of GT generated pollutants:

Products of combustion and their consequences; Mechanisms of formation of GT pollutants; Effects on the environment and/or human health; Overview of limitation strategies and associated challenges; Low emissions combustion systems for aero and stationary gas turbines; Emissions legislation and targets.

GT combustor heat transfer and cooling:

Combustor buckling and cracking; Need for efficient methods of liner cooling; Heat transfer processes (Internal and external radiation, internal and external convection, conduction); Calculation of uncooled liner temperature; Effect of chamber variables on heat transfer terms, liner wall temperature and liner life; Film cooling techniques; Advanced wall cooling techniques; Combustor liner materials and thermal barrier coatings.

GT fuels

Appraise types and properties of fuels; Methodologies to calculate combustion temperatures for various fuel types, mixture strengths and pressures (both non-dissociated and dissociated).

Computational methods for GT Combustors

Role of CFD in combustor design and development; Application of CFD for preliminary design, prognostics and diagnostics of combustion systems.

Introduction to GT afterburners:

Requirement and principle of afterburning; Effects of afterburning on engine performance; General arrangement, main components and design features of afterburners; Ignition methods for GT afterburners; Control requirements and methods for engines with afterburners; Considerations for selection of convergent and convergent-divergent nozzles.

On successful competition of this module you should be able to:

1. 1. Explain and evaluate the concepts underpinning the design of gas turbine combustors and reheat systems for both aero and stationary gas turbines, and explain the influence of the design choices on overall engine configuration and performance.
2. 2. Assess the influence of: fuel types and preparation, combustion efficiency, ignition requirements, diffuser performance, operational criteria, pollutant emissions and legislation, cooling and material technology on combustor sizing, design and performance.
3. 3. Apply heat transfer techniques to the calculation of combustor liner temperature and assess the effect of materials, advanced cooling methods and thermal barrier coatings on the life of a combustor liner.
4. 4. Employ methodologies to calculate combustion temperatures for various fuel types, mixture strengths and pressures.
5. 5. Distinguish between simple and more advanced computational methods for combustor performance prediction in terms of their modelling and capabilities.

To familiarise you with engine systems or engine designs for stationary and aero gas turbines and technical reporting by examples and sources systematic analysis.

Assessments of engine systems, auxiliaries, families of engines, and/or engine and component designs for both aero and stationary gas turbines are addressed by means of a 'Systems Symposium', run by the MSc class. Topics covered by the systems symposium include: intake systems for aero engines and industrial gas turbines; anti-icing systems for aeroengines and industrial gas turbines; start systems for aeroengines and industrial gas turbines; start sequences for industrial gas turbines; compressor bleed and variable guide vanes; variable geometry nozzle guide vanes; gas path sealing of aero gas turbines; noise control of gas turbines; air filtration for industrial gas turbines; compressor and turbine cleaning systems; full authority and other electronic control systems; key gas turbine component design technologies, etc. Topics may also cover design technologies of gas turbine engines and their components, different families of engine products of major gas turbine manufacturers in different countries, comparison of competitive engines, etc. The objective is to undertake an evaluation of a specified aspect of gas turbine engineering, to make a presentation and to provide a technical review paper or design and assessment on a particular subject.Another aspect of the module is that the presentations are made in a conference format which requires you to work together to plan, organise and execute the events.


Outline syllabus for a few sample individual topics:
• Ignition system: Requirements and problems of altitude relight. Types of system -booster coils, high frequency, high energy and their applications.
• Starting Systems: Electrical systems - low and high voltage, turbine systems- cartridge, iso-propyl nitrate, fuel-air, gas turbine, low pressure air and hydraulic systems and their applications.
• Air systems: requirements, methods of cooling, pressure balancing of end loads, sealing, and applications.
• Preliminary design of axial high pressure compressor: requirements, design criteria, preliminary design, analysis of design results, etc.
• CFM56 engines: development history, OEM, product description, key technologies, future development, etc.

On successful completion of this module you should be able to:

1. 1. Compose a structured technical report in the form of a conference paper and a technical presentation.
2. 2. Conduct a systematic analysis of a range of sources to identify, analyse and assess the main technologies of a key aspect of gas turbine engineering.
3. 3. Report and defend the technical outcomes of the systematic analysis in the form of a conference paper and presentation.
4. 4. Work effectively with others in groups to deliver a Gas Turbine Systems Symposium on the basis of a scientific conference.
5. 5. Collaborate in different capacities to formulate a business/management plan to market and communicate the Engine Systems Symposium to the wider gas turbine community for encouraging the attendance of external agencies

The importance of technology leadership in driving the technical aspects of an organisation’s products, innovation, programmes, operations and strategy is paramount, especially in today’s turbulent commercial environment with its unprecedented pace of technological development. Demand for ever more complex products and services has become the norm. The challenge for today’s manager is to deal with uncertainty, to allow technological innovation and change to flourish but also to remain within planned parameters of performance. Many organisations engaged with technological innovation struggle to find engineers with the right skills. Specifically, engineers have extensive subject/discipline knowledge but do not understand management processes in organisational context. In addition, STEM graduates often lack interpersonal skills.

• Engineers and Technologists in organisations:
  • the role of organisations and the challenges facing engineers and technologies,
• People management:
  • understanding you, understanding other people, working in teams and dealing with conflicts.
• The Business Environment:
  • understanding the business environment; identifying key trends and their implications for the organisation.
• Strategy and Marketing:
  • developing effective strategies, focusing on the customer, building competitive advantage, the role of strategic assets.
• Finance:
  • profit and loss accounts, balance sheets, cash flow forecasting, project appraisal.
• New product development:
  • commercialising technology, market drivers, time to market, focusing technology, concerns.
• Business game:
  • Working in teams (companies), you will set up and run a technology company and make decisions on investment, R&D funding, operations, marketing and sales strategy,
• Negotiation:
  • preparation for negotiations, negotiation process, win-win solutions.
• Presentation skills:
  • understanding your audience, focusing your message, successful presentations, getting your message across.

On successful completion of this module you should be able to:

• 1. Recognise the importance of teamwork in the performance and success of organisations with particular reference to commercialising technological innovation,
• 2. Operate as an effective team member, recognising the contribution of individuals within the team, and capable of developing team working skills in yourself and others to improve the overall performance of a team,
• 3. Compare and evaluate the impact of the key functional areas (strategy, marketing and finance) on the commercial performance of an organisation, relevant to the manufacture of a product or provision of a technical service,
• 4. Design and deliver an effective presentation that justifies and supports any decisions or recommendations made,
• 5. Argue and defend your judgements through constructive communication and negotiating skills.

To familiarise the course member with various operations of gas turbines and other driven rotating machines.

Gas Turbine Operations:
• An overview of the different operational regimes for gas turbine application. This explores base load, peak load, standby and backup operations, alongside their individual operational requirements. It also includes engine control modes such as operating at approximately constant exhaust gas temperature and load-following mode. Analysis of gas turbine performance and health using machine sensor data from actual operation is also a key part. This part also highlights the use and impact of ancillary equipment (air filtration and compressor washing systems) in improving the performance and extending the operating hours of gas turbine machines. Gas turbine operational flexibility for back-up of renewable power.

Steam Turbine Operations:
• Steam turbine fundamentals, applications and selection. This includes an overview of steam turbine plants operating on fossil fuel - combined cycle gas turbines (CCGT) and combined heat and power (CHP) operations. It also covers aspects of heat recovery systems, condensers, pumps and other auxiliary equipment.

Diesel Engines for Heat and Power:
• Diesel engine fundamentals; theory and principles. This includes 2-stroke (crosshead engine) and 4-stroke (trunk piston) types, their installation and operations. Utilisation of diesel engine waste heat recovery for district heating hot water systems, cooling systems using chiller and fresh water generation are the common applications explored. Diesel engine fuels and the means of controlling exhaust emissions are included.

On successful completion of this module you should be able to:

1. 1. Evaluate gas turbine performance using machine data from actual operations.
2. 2. Assess engine performance deterioration, as well as propose improved approaches in enhancing performance during operation.
3. 3. Distinguish and compare key components and parameters and further relate them to steam turbine theory, performance and operation.
4. 4. Differentiate and assess the applications of steam turbines.
5. 5. Calculate diesel engine performance, differentiate between 2-stroke and 4-stroke engines and the operational requirements, also with respect to heat and power.

To familiarise you with various marine propulsion technologies, propulsion auxiliary and their integration

The module will be covered in the following four parts:

1. Ship Propulsion Systems
   • An overview of Gas Turbine, Diesel, Steam propulsion systems and their combination. This will include evaluating their advantages/disadvantages, optimal performance of various configurations, performance analysis and integration.
• An overview of hybrid and electric technology for ship propulsion and their relative merits and demerits.
2. Ships Auxiliary systems
   • Introduction to ship design concepts, fundamentals of ship resistance, control surfaces, boundary layers and propulsion coefficients.
   • Overview of propulsion train which includes different types of propellers, shafting, ‘A’ Brackets, gearbox and other components.
   • Understanding principles of hull vibration, propeller cavitation, shaft torsional vibration and their effect on the propulsion system performance.
3. Propulsion System Integration
   • This part focuses on understanding the integration of propulsion system which includes the prime-movers, auxiliaries, and other associated systems/ control mechanism.
   • Introduction to ÃÀ¼§¸ó’s Poseidon+ simulation for propulsion system integration.
4. Alternative fuels and Regulatory framework
   • An overview of predicted future energy trends/sources, alternative fuels for marine usage (natural gas, di-methyl ether, hydrogen, ammonia, nuclear options, photo-voltaic, etc..) in the light of decarbonisation in the maritime sector.
   • Introduction to emissions, MARPOL, SOLAS, Flag & Port state, marine safety issues etc.

On successful completion of this module you should be able to:

1. 1. Compare different marine propulsions technologies, evaluate their performance, and specify parameters for selecting a suitable propulsion system.
2. 2. Distinguish between various ship auxiliaries, their performance and examine suitability for a given propulsion system.
3. 3. Evaluate the performance of a given propulsion system as a whole and highlight integration issues.
4. 4. Compare different types of fuels/energy sources for a given propulsion system and analyse its compliance with the prevailing regulatory and safety framework.
5. 5. Assess Techno-Economic parameters and sustainability of the selected propulsion system.